METAL PLATE
AND ANGLE ROLL
FORMING MACHINES
INTRODUCING THE WORK HORSE
OF PLATE & ANGLE ROLLS
We are the official manufacturer of WDM Rolls. If you need metal rolled we have you covered. Below is the different roll configurations that we offer. Each model can come in a variety of sizes and we can custom build a roll to best suit your needs. Please contact us and we can help consult you in finding the best roll for you.
310 SERIES PLATE ROLL
The WDM 310 Series plate roll is built primarily for the sheet metal industry and small maintenance shops. The 310 has been simplified to a no hydraulic/all electric design. Both the roll drive and the power bending adjustment drive (optional) are powered by an electric helical gear motor.
Standard Features
- 1045 steel rolls machined to T63 micro inches
- Crowned rolls
- Total electric operation
- Near instant start/stop/reverse
- Forward & reverse guarded foot switch for roll rotation
- Rule and pointer to show roll position
- Spur gear 2 roll drive
- 3 phase 230/430 volts 60hz electrics
- Electrics to NFPA-79 specifications
- 24VDC control circuit
- Safety/emergency stop cable on 3 sides of the machine
- Pinch roll starting groove
- Overload protected
- NEMA premium efficient electric helical gear motor with holding brake for roll rotation
- Gearbox lubed for life
- Heavy duty all gear drive
- Haze gray epoxy and blue enamel finish (V.O.C. compliant)
- Sealed ball bearings on all main points
- Rolls tilt for cone rolling
- Manually operated latch handle with swing out top roll
- Accurately machined, compact, streamlined, and all welded steel frame
- Variable roll speed 0-20 FPM
- Made in USA
Options
- Hardened and polished rolls 55-60 Rc. (1045 flame hardened) G32 finish
- Other alloys and finishes are available
- Additional squaring grooves in lower rolls
- Circular grooves in rolls for rolling rods or sheets with wire edges 3/8, 1/2, and 5/8
- Other special circular grooves for extrusions etc.
- Cone attachment
- Power bending adjustment
- Third roll drive
- Extended shaft and dies for rolling angles, flats, rounds, and pipes (5 and 6 models only)
- DRO for roll position instead of rule and pointer
- Mechanical DRO to show pinch roll position
403 SERIES 4-ROLL DOUBLE PINCH PLATE BENDING MACHINE
The WDM 403 Series is essentially an initial pinch plate machine with an additional roll on the front side of the pinch rolls. The advantage of this type of machine is that you can roll the workpiece from the leading to trailing edge with one entry resulting in negligible flats.
Standard Features
- 1045 steel rolls machined to T63 micro inch finish
- Crowned rolls
- Total hydraulic operation
- Instant start/stop/reverse
- 2 roll drive
- 3 phase 230/460 volts 60hz electrics
- Electrics to NFPA-79 specifications
- 24VDC control circuit
- Safety/emergency stop cable on 3 sides of the machine.
- Overload protected
- TEFC main motor
- Quiet hydraulic system
- Haze gray epoxy and blue enamel finish (V.O.C. compliant)
- Sealed spherical roller bearings on all main points
- Bending rolls tilt for cone rolling
- DRO to show roll position
- Roving pendant control
- Hydraulically actuated drop-end
- Accurately machined, compact, streamlined, and all welded steel frame
- Rolls driven direct via hydraulic motor or gear speed reducers
- Variable roll speed 0-22 FPM
- 1 year warranty
- Made in USA
Options
- Hardened only rolls 55-60 Rc. (1045 flame hardened) T63 finish.
- Hardened and polished rolls 55-60 Rc. (1045 flame hardened) G32 finish
- Other alloys and finishes are available
- Squaring grooves in pinch roll
- Circular grooves in rolls for rolling rods or sheets with wire edges 3/8, 1/2, and 5/8
- Other special circular grooves for extrusions etc.
- Dual guarded foot switch for roll rotation and pinch roll up/down
- Cone attachment
- Control upgrade
- Pinch roll trim (recommended if you roll a lot of cones)
101 SERIES PLATE ROLL
The WDM 101 Series is a pinch pyramid style roll making it a very versatile machine. It can roll square and rectangle tubing, channel, I-beam on flange, and fabricated panels without additional attachments.
Standard Features
- 1045 steel rolls machined to T63 micro inch finish
- Crowned rolls
- Total hydraulic operation
- Instant start/stop/reverse
- 3 roll drive
- 3 phase 230/460 volts, 60HZ electrics
- Electrics to NFPA-79 specifications 24VDC control circuit
- Safety/Emergency stop cable on 3 sides of the machine
- Overload protected
- TEFC main motor
- Quiet hydraulic system
- Haze gray epoxy and blue enamel finish (V.O.C. compliant)
- Sealed spherical roller bearings on all main points
- 1 squaring groove in far roll
- Rolls tilt for cone rolling
- Rolls driven through efficient spur gear drives or planetary speed reducers
- Roving pendant control
- DRO to show roll position
- Hydraulically actuated drop-end
- Accurately machined, compact, streamlined, and all welded steel frame
- Variable roll speed 0-22 FPM
- 1 year warranty
- Made in USA
Options
- Hardened only rolls 55-60 Rc. (1045 flame hardened) T63 finish
- Hardened and polished rolls 55-60 Rc. (1045 flame hardened) G32 finish
- Other alloys and finishes are available
- Additional squaring grooves in lower rolls
- Circular grooves in rolls for rolling rods or sheets with wire edges 3/8, 1/2, and 5/8
- Other special circular grooves for extrusions etc.
- Forward & reverse guarded foot pedal for roll rotation
- Cone attachment
- Control upgrade
- Non-electric version
- Side supports
- Overhead supports
K SERIES PLATE BENDING MACHINE
The WDM K Series initial pinch plate bending machines are well designed, robust machines that feature a wedge actuated pinch roll positioning system, as well as a fully hydraulic operation.
Standard Features
- 1045 steel rolls machined to T63 micro inch finish.
- Crowned rolls
- Total hydraulic operation
- Instant start/stop/reverse
- 2 roll drive
- 3 phase 230/430 volts 60hz electrics
- Electrics to NFPA-79 specifications
- 24VDC control circuit
- Roll speed infinitely variable 0-22 FPM
- Safety/Emergency stop cable on 3 sides of the machine
- Overload protected
- TEFC main motor
- Quiet hydraulic system
- Haze gray epoxy and blue enamel finish (V.O.C. compliant)
- Sealed spherical roller bearings on all main points
- Bending roll tilts for cone rolling
- Accurately machined, compact, streamlined, and all welded steel frame
- Rolls driven direct via hydraulic motor or gear speed reducers
- Roving pendant control
- DRO to show roll position
- Horizontal starting groove in pinch roll
- Hydraulically actuated drop-end
- 1 year warranty
- Made in USA
Options
- Hardened only rolls 55-60 Rc. (1045 flame hardened) T63 micro inch finish
- Hardened and polished rolls 55-60 Rc. (1045 flame hardened) G32 finish
- Other alloys and finishes are available
- Additional squaring grooves in lower rolls
- Circular grooves in rolls for rolling rods or sheets with wire edges 3/8, 1/2, and 5/8
- Other special circular grooves for extrusions etc.
- Dual guarded foot pedal for roll rotation and pinch roll up/down
- Cone attachment
- Pinch roll trim
- Third roll drive
- Control upgrade
- Non-electric version
- Side supports
AR SERIES ROLLER
The WDM AR Series is a roll that can be equipped with changeable dies for rolling angle, pipe, tubing, channel, and I-beam
Standard Features
- Unitized steel construction
- Flame hardened alloy steel shafts and arbors
- Total hydraulic operation
- Instant start/stop/reverse
- 2 speed/variable speed
- 1 set universal dies; rolls:
- Angle leg in and out
- Tee bar leg in and out
- Flats on edge and on flat
- Square and small rounds
- Accurately machined and hardened dies
- 3 roll drive (all machines except 4 roll)
- Roving pendant control
- DRO to show roll position
- Electrics to NFPA specifications
- 24VDC control circuit
- Safety stop/emergency stop mushroom buttons
- Overload protection
- TEFC main motor
- Quiet integrated hydraulic system
- Painted haze grey epoxy and blue enamel
- sealed spherical roller bearings on all main points
- Non-lube, minimum maintenance technology throughout
- Heavy gear drive with very strong efficient tooth profile, most gears cut in our own shop.
- Made in USA
Options
- Control upgrade
- Special dies
- Special guides
- Overhead supports
- Non-electric version
- Special electrics
- Special paint
- High speed version
